Page 1 of 2
need help....kpro issues
Posted: Wed Mar 12, 2008 6:53 am
by vivalive
my Iat engine is on after installed kpro, and it lock my cams at 0 degree..
i need help fixing this issues.. could someone help me.. i've checked all the wiring and refered to the services manual..
k20a3 2005 model rsx.
Posted: Wed Mar 12, 2008 10:21 am
by Spunkster
Have you tried the ecu in another vehicle?
Posted: Wed Mar 12, 2008 12:24 pm
by vivalive
no i havn't... my kpro is brand new shouldn't there be no problem?
by the way. its a type-s ecu k-kpro.
Posted: Wed Mar 12, 2008 12:26 pm
by vivalive
Spunkster wrote:Have you tried the ecu in another vehicle?
does the type-s and base rsx share the same sensor on the throttle body?
i know the throttle body is different but not sure about the sensor?
Posted: Wed Mar 12, 2008 4:50 pm
by Spunkster
The sensors are all the same. Please try the ecu on another vehicle. This will tell you if it is a problem with your ecu or with your car.
Posted: Wed Mar 12, 2008 5:25 pm
by vivalive
Spunkster wrote:The sensors are all the same. Please try the ecu on another vehicle. This will tell you if it is a problem with your ecu or with your car.
will i have check engine if i ran my stock 2005 ecu with 2004 o2 sensor?
Posted: Thu Mar 13, 2008 9:36 am
by Spunkster
You have asked this before. You must use the 02-04 o2 sensor with the K-Pro. You are trignto determine if there is a problem with the IAT, so don't worry about other errors when testing. Just look for the IAT error.
Posted: Thu Mar 13, 2008 11:27 am
by vivalive
Spunkster wrote:You have asked this before. You must use the 02-04 o2 sensor with the K-Pro. You are trignto determine if there is a problem with the IAT, so don't worry about other errors when testing. Just look for the IAT error.
i've change the 1st o2 sensor, do i need to change the o2 after the cat?
Posted: Thu Mar 13, 2008 2:35 pm
by Spunkster
no
Posted: Thu Mar 13, 2008 3:39 pm
by vivalive
when i unplug my IAT kpro is still throwing " IAT LOW VOLTAGE" and the temperature reading is the same 95f.
what should i do? my turbo kit is comming in next week... i want to get this fixed. i don't want to use Emange!
type-s ecu/ 05 base rsx.
Posted: Thu Mar 13, 2008 4:03 pm
by vivalive
could i only buy a new harness?
Posted: Thu Mar 13, 2008 4:57 pm
by Spunkster
There is no need to buy a harness since you have not completed all the troubleshooting steps yet. You need to try this ecu in another vehicle to see if it is getting the same IAT error there.
Posted: Thu Mar 13, 2008 6:25 pm
by vivalive
Spunkster wrote:There is no need to buy a harness since you have not completed all the troubleshooting steps yet. You need to try this ecu in another vehicle to see if it is getting the same IAT error there.
there isn't another 05-06 rsx i could try on.... could i try it on an 02-04?
Posted: Fri Mar 14, 2008 9:32 am
by Spunkster
Yes you can try it on any RSX, just don't use the adapter if it's an 02-04.
Posted: Fri Mar 14, 2008 3:35 pm
by vivalive
Spunkster wrote:Yes you can try it on any RSX, just don't use the adapter if it's an 02-04.
today i took out my Iat, and figure out its cooked/melted. could there be a short somewhere?