Page 1 of 1

8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Fri May 23, 2025 5:27 am
by mrspades252
I know Ill have to get it tuned eventually but I was wondering to see if anybody has a calibration or something similar?

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Fri May 23, 2025 4:49 pm
by CalibratEd
Run a Hondata base calibration with the mods closes to yours until you can get it tuned. I can check how it’s running if you post the calibration and a datalog.

-Ed

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Sat May 24, 2025 4:24 pm
by mrspades252
Will do ASAP, i actually took my suspension apart and will be installing coilovers! Thanks!

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Sun May 25, 2025 8:07 pm
by CalibratEd
mrspades252 wrote: Sat May 24, 2025 4:24 pm Will do ASAP, i actually took my suspension apart and will be installing coilovers! Thanks!
No problem. Sounds good.

-Ed

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Mon Jun 09, 2025 4:49 pm
by mrspades252
CalibratEd wrote: Sun May 25, 2025 8:07 pm
mrspades252 wrote: Sat May 24, 2025 4:24 pm Will do ASAP, i actually took my suspension apart and will be installing coilovers! Thanks!
No problem. Sounds good.

-Ed
Alright Ed, i ran into a lot of issues over the past few weeks with this car since i posted. Old suspension were seized, and had idle/drivability issues, which prevented me from replying back! I finally got the coilovers installed and fixed the idle/drivability issues (replaced maf sensor)! I will start datalogging on saturday but am unsure on which calibration to use! Will you still be able to give me a hand?

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Mon Jun 09, 2025 6:37 pm
by CalibratEd
Sorry to hear that. Like I said prior, select a file with mods closes to yours and I can let you know how it’s running.

-Ed

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Tue Jun 10, 2025 2:16 am
by mrspades252
How should i datalog? Locally and on the freeway?

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Tue Jun 10, 2025 7:19 am
by CalibratEd
mrspades252 wrote: Tue Jun 10, 2025 2:16 am How should i datalog? Locally and on the freeway?
Both are fine. Just refrain from doing any wide open throttle pulls.

-Ed

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Sat Jun 14, 2025 8:00 am
by mrspades252
this is the calibration i used

here is a datalog!

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Tue Jun 17, 2025 11:13 am
by mrspades252
heres another datalog

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Thu Jun 26, 2025 8:43 pm
by CalibratEd
The fueling is not far off and you do not have any knock.

- Ed

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Tue Jul 01, 2025 4:03 pm
by mrspades252
Awesome so i should be able to drive it around for the time being until i can get it dyno tuned?

Re: 8th gen FBO hybrid racing, 3” thermal r&d and plm headers

Posted: Sun Jul 06, 2025 10:37 am
by CalibratEd
Yes.

-Ed