Page 1 of 1
SManager V2.8.8
Posted: Thu Jan 16, 2025 8:01 pm
by Hondata
SManager V2.8.8 (16 Jan 2025)
- Added closed loop inactivity timeout
- [S300 V3] Firmware version 23
- [S300 V3] Fixed ethanol disabling after ECU power cycle.
Download
here
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Re: SManager V2.8.8
Posted: Sat Jan 25, 2025 9:21 am
by DatLife84
Just updated to the v2.8.8 and now cannot change the values in Pressure vs Duty Cycle in the boost control tab.
Re: SManager V2.8.8
Posted: Mon Jan 27, 2025 10:18 am
by Spunkster
Post the calibration you are trying to make changes to.
Re: SManager V2.8.8
Posted: Fri Jan 31, 2025 11:49 am
by 1 bad em1
Is the 'closed loop inactivity timeout' intended to fix the issue where closed loop becomes inactive/freezes/quits working? And if so, do we simply raise the timeout value to help alleviate the problem?
Re: SManager V2.8.8
Posted: Sat Feb 01, 2025 6:05 am
by DatLife84
Spunkster wrote: Mon Jan 27, 2025 10:18 am
Post the calibration you are trying to make changes to.
Ek Turbo 1 (15psi 9k).skl
Re: SManager V2.8.8
Posted: Sun Feb 02, 2025 10:52 am
by 1 bad em1
Hondata wrote: Thu Jan 16, 2025 8:01 pm
SManager V2.8.8 (16 Jan 2025)
- Added closed loop inactivity timeout
- [S300 V3] Firmware version 23
- [S300 V3] Fixed ethanol disabling after ECU power cycle.
Download
here
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Let me know when you have a chance about the 'closed loop inactivity timeout', is this intended to resolve the issue where people have their closed loop stop working (typically after deceleration/full lean/tip out)? I believe it was something to do with the ECU thinking closed loop was malfunctioning due to the o2 reading being too high for too long, so maybe this 'inactivity timeout' value is supposed to increase the length of time before the ecu disables closed loop? Let me know if that is correct, I had this problem happen a few times but it is random, if this resolves that problem that would be great.
Re: SManager V2.8.8
Posted: Mon Feb 03, 2025 11:02 am
by Spunkster
DatLife84 wrote: Sat Feb 01, 2025 6:05 am
Spunkster wrote: Mon Jan 27, 2025 10:18 am
Post the calibration you are trying to make changes to.
Ek Turbo 1 (15psi 9k).skl
You do not have the gear based target boost selected.
Re: SManager V2.8.8
Posted: Mon Feb 03, 2025 11:02 am
by Spunkster
1 bad em1 wrote: Sun Feb 02, 2025 10:52 am
Hondata wrote: Thu Jan 16, 2025 8:01 pm
SManager V2.8.8 (16 Jan 2025)
- Added closed loop inactivity timeout
- [S300 V3] Firmware version 23
- [S300 V3] Fixed ethanol disabling after ECU power cycle.
Download
here
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Let me know when you have a chance about the 'closed loop inactivity timeout', is this intended to resolve the issue where people have their closed loop stop working (typically after deceleration/full lean/tip out)? I believe it was something to do with the ECU thinking closed loop was malfunctioning due to the o2 reading being too high for too long, so maybe this 'inactivity timeout' value is supposed to increase the length of time before the ecu disables closed loop? Let me know if that is correct, I had this problem happen a few times but it is random, if this resolves that problem that would be great.
It may help. Try it and see if the issue continues.
Re: SManager V2.8.8
Posted: Mon Feb 03, 2025 4:18 pm
by 1 bad em1
Spunkster wrote: Mon Feb 03, 2025 11:02 am
1 bad em1 wrote: Sun Feb 02, 2025 10:52 am
Hondata wrote: Thu Jan 16, 2025 8:01 pm
SManager V2.8.8 (16 Jan 2025)
- Added closed loop inactivity timeout
- [S300 V3] Firmware version 23
- [S300 V3] Fixed ethanol disabling after ECU power cycle.
Download
here
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Let me know when you have a chance about the 'closed loop inactivity timeout', is this intended to resolve the issue where people have their closed loop stop working (typically after deceleration/full lean/tip out)? I believe it was something to do with the ECU thinking closed loop was malfunctioning due to the o2 reading being too high for too long, so maybe this 'inactivity timeout' value is supposed to increase the length of time before the ecu disables closed loop? Let me know if that is correct, I had this problem happen a few times but it is random, if this resolves that problem that would be great.
It may help. Try it and see if the issue continues.
It looks like this was indeed intended to fix that issue that was noted by several people in 'closed loop malfunction' thread. Hondata admin posted in that thread that this release exposed that timeout value to try to eliminate the problem. I'll be testing it out once spring rolls around, glad to hear it! It's been several years of this problem so I'm happy to hear something is finally being done to try to fix it.
Re: SManager V2.8.8
Posted: Wed Feb 05, 2025 3:40 am
by DatLife84
Thank you