Page 1 of 2
FlashProManager 4.3.3
Posted: Fri Aug 16, 2024 2:16 pm
by Hondata
FlashProManager 4.3.3 (16 Aug 2024)
- [FK2/FK8/FL5/DE5] Added CANFlex support
Download
here
https://hondata.com/canflex-10thgen-2.0
https://hondata.com/canflex-11thgen-2.0
Re: FlashProManager 4.3.3
Posted: Tue Aug 20, 2024 10:31 pm
by Rodrigosantos
Hello, pop and bang for Fk2 is not working, the overun fuel is working but not the retard table
Re: FlashProManager 4.3.3
Posted: Wed Aug 21, 2024 9:44 am
by Hondata
Please provide your calibration and datalogs and an explanation of what driving modes you were using when testing.
Re: FlashProManager 4.3.3
Posted: Fri Aug 23, 2024 6:24 am
by Rodrigosantos
Already sent it by email!
Using sport mode or normal mode the ignition on deceleration is always 7/8 degrees, no matter what retard do you put in the table! I’ve tried some retard values and nothing is working! Tried stage 1 and stage 2 pops and nothing change in the ignition. It’s like the ecu is not assuming that table! I don’t know what strategie you use for this table but I think some other table in the background is correcting the values! Hope you understand!
Thank you!
Re: FlashProManager 4.3.3
Posted: Fri Aug 23, 2024 8:42 am
by Hondata
Without a datalog and a matching calibration and an explanation of the driving mode used for the datalog I can't address this.
Re: FlashProManager 4.3.3
Posted: Fri Aug 23, 2024 9:01 am
by Rodrigosantos
I send it by email the calibration the datalog with r mode and explanation of the problem, check your email
Re: FlashProManager 4.3.3
Posted: Fri Aug 23, 2024 9:09 am
by Rodrigosantos
R mode
Re: FlashProManager 4.3.3
Posted: Fri Aug 23, 2024 2:38 pm
by Hondata
Please datalog on the FlashPro - the datalog does not have enough resolution.
And also provide a corresponding datalog in standard mode.
Re: FlashProManager 4.3.3
Posted: Sat Aug 24, 2024 7:34 am
by Rodrigosantos
hello,
i hope this time is good
thanks
Re: FlashProManager 4.3.3
Posted: Mon Aug 26, 2024 8:29 pm
by KT7788
FB:
Comfort + R mode
Fuel delay - Working. if add too much (Example 2 sec delay), the car feels like choke/ jerk jerk during decel not smooth.....
The POP and bang Function , seems like intermittent working
With selection set to retard 15 / 20 /25 , it seem that other table/function is preventing it to achieve the require result
- example if you drive/rev to 5k rpm , release the throttle, it should fall into decel zone with the set retard IGN
- seems intermittent working
Attach if the log file
- please pardon me if the log file is no good...
- aleast i try
Re: FlashProManager 4.3.3
Posted: Mon Aug 26, 2024 8:29 pm
by KT7788
Thanks
Re: FlashProManager 4.3.3
Posted: Mon Aug 26, 2024 8:38 pm
by KT7788
The pop and bang *Live Function is working ?
the intend is to *live adjust the parameters but seem like not working
Re: FlashProManager 4.3.3
Posted: Fri Aug 30, 2024 12:51 pm
by Hondata
Removing FK2 pops and bangs until we have a better chance to test this.
Re: FlashProManager 4.3.3
Posted: Sat Aug 31, 2024 12:56 am
by KT7788
Sad... please don't give up.
Doing great. Abit more here n there will reach the goal
Cheers
Re: FlashProManager 4.3.3
Posted: Fri Sep 06, 2024 2:55 pm
by high718
Recently installed my CANFLEX kit on my fk8. Was initially on the sirimoto kit. At the time of install I was at 44% ethanol as per the innovate gauge. On my hondata app and iPhone on the canflex kit starts at 49% ethanol and as I drive the percentage drops to 6-8 ethanol. I am currently on the latest flash pro firmware 4.3.4. How/what can I do to get the ethanol percentage correct.