Page 1 of 2
Analog inputs not working after firmware V2.8.4
Posted: Thu Dec 21, 2023 8:24 pm
by kseriescivic
Opened hondata after updating to V2.8.4 firmware Dec 5th update and none of my analog input sensors are reading on the display tab or during datalogging.
Is there something I’m missing or need to do to get them to work?
Re: Analog inputs not working after firmware V2.8.4
Posted: Fri Dec 22, 2023 9:48 am
by Spunkster
With everything plugged in and the ignition in the on position, go to the Help menu and click on “send feedback”. Include a detailed description of the issue.
Re: Analog inputs not working after firmware V2.8.4
Posted: Wed Dec 27, 2023 2:31 pm
by bradheller29
Also having this issue. I did "send feedback" hoping it gets resolved. Thanks.
Re: Analog inputs not working after firmware V2.8.4
Posted: Wed Dec 27, 2023 3:13 pm
by kseriescivic
Okay I was wondering if anyone else was having this issue. Same, hopefully it gets resolved!
Re: Analog inputs not working after firmware V2.8.4
Posted: Sat Dec 30, 2023 9:59 pm
by Jnguyen
Having save issue, no readings on analogs. When does Hondata usually update firmware again ?
Re: Analog inputs not working after firmware V2.8.4
Posted: Sun Dec 31, 2023 9:54 am
by Hondata
Please can you tell us what S300 you have. The best way would be in the S300 window, S300 tab under hardware, the hardware version and processor type. There are 6 different hardware types so knowing this will cut down the amount of time it takes to fix this.
Also it would be good to know how the analog input has been configured, and what type of datalogging you are doing.
Re: Analog inputs not working after firmware V2.8.4
Posted: Mon Jan 01, 2024 7:14 pm
by kseriescivic
Here’s what it says under about. I’ll have to connect to the ecu tomorrow to look under the s300 tab.
Re: Analog inputs not working after firmware V2.8.4
Posted: Tue Jan 02, 2024 7:51 am
by Jnguyen
Hondata wrote: Sun Dec 31, 2023 9:54 am
Please can you tell us what S300 you have. The best way would be in the S300 window, S300 tab under hardware, the hardware version and processor type. There are 6 different hardware types so knowing this will cut down the amount of time it takes to fix this.
Also it would be good to know how the analog input has been configured, and what type of datalogging you are doing.
trying to data log oil pressure and fuel pressure, analog 1 and 2. getting voltage signal to s300 v3 but not reading on display.
Re: Analog inputs not working after firmware V2.8.4
Posted: Tue Jan 02, 2024 1:35 pm
by DaX
I'm sure you guys are on it, but I'll also mention that I'm having this issue as well. S300V3, wired in a pressure sensor, sending to analog 1. I verified correct wiring and scaling, I am getting the correct voltage out of the sensor, but am not getting anything to show on the display or on the sensors tab.
Re: Analog inputs not working after firmware V2.8.4
Posted: Tue Jan 02, 2024 4:08 pm
by Jnguyen
DaX wrote: Tue Jan 02, 2024 1:35 pm
I'm sure you guys are on it, but I'll also mention that I'm having this issue as well. S300V3, wired in a pressure sensor, sending to analog 1. I verified correct wiring and scaling, I am getting the correct voltage out of the sensor, but am not getting anything to show on the display or on the sensors tab.
Same here I get “0” values
Re: Analog inputs not working after firmware V2.8.4
Posted: Wed Jan 03, 2024 1:03 pm
by Hondata
Please, please tell us what hardware you have as outlined above. And provide a calibration if you can.
Re: Analog inputs not working after firmware V2.8.4
Posted: Wed Jan 03, 2024 3:56 pm
by Jnguyen
Hondata wrote: Sun Dec 31, 2023 9:54 am
Please can you tell us what S300 you have. The best way would be in the S300 window, S300 tab under hardware, the hardware version and processor type. There are 6 different hardware types so knowing this will cut down the amount of time it takes to fix this.
Also it would be good to know how the analog input has been configured, and what type of datalogging you are doing.
Here’s my hardware and processor
Re: Analog inputs not working after firmware V2.8.4
Posted: Wed Jan 03, 2024 5:10 pm
by Spunkster
This should be fixed in a release of software tomorrow.
Re: Analog inputs not working after firmware V2.8.4
Posted: Thu Jan 04, 2024 2:00 pm
by Jnguyen
Spunkster wrote: Wed Jan 03, 2024 5:10 pm
This should be fixed in a release of software tomorrow.
when will this new firmware be ready?
Re: Analog inputs not working after firmware V2.8.4
Posted: Thu Jan 04, 2024 2:24 pm
by kseriescivic
Not sure if you still need this but here’s my hardware and processor