Page 1 of 2
FlashProManager 3.8.8
Posted: Mon Feb 21, 2022 5:14 pm
by Hondata
V3.8.8 (21 Feb 2022)
- Firmware updated to version 208
- [FK2] Added idle fuel pressure, flex fuel support, traction control, full throttle shift and anti-lag.
- [FK8] Added fuel pump PID and feed forward tables
- [FK8] Added support for 2020 Asia model 5BF-U23
- [2019+ RDX] Added support for US 2022 model 5YF-AD2
- [2017+ Civic Si] Added support for Brazil 2019 model 5AM-M11
Download
here
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Re: FlashProManager 3.8.8
Posted: Tue Feb 22, 2022 3:24 am
by Bain
Hi Admin
WIth the Flex Fuel for the FK2- what kits are compatable?
Same as the FK8 or the 1.5T?
Fuel-IT kits?
thanks
Re: FlashProManager 3.8.8
Posted: Tue Feb 22, 2022 8:47 am
by Hondata
Any device that outputs an analog voltage rather than a frequency signal.
Re: FlashProManager 3.8.8
Posted: Wed Feb 23, 2022 3:21 am
by Bain
Hondata wrote: Tue Feb 22, 2022 8:47 am
Any device that outputs an analog voltage rather than a frequency signal.
Thank you.
Re: FlashProManager 3.8.8
Posted: Wed Feb 23, 2022 10:48 am
by MauiSI
Upgraded to the latest release and when I plug my flashpro in, I get prompted to update the firmware. It is stuck and does not update. I even let it run overnight. Any suggestions?
Re: FlashProManager 3.8.8
Posted: Wed Feb 23, 2022 11:13 am
by Spunkster
Unplug the FlashPro from the vehicle and USB, then only plug in the USB and try again.
Re: FlashProManager 3.8.8
Posted: Wed Feb 23, 2022 3:45 pm
by Hondata
Hondata wrote: Mon Feb 21, 2022 5:14 pm
Please only reply to this thread with issues & questions specific to the changes in this release. For all other problems start a new thread under the appropriate vehicle category.
Re: FlashProManager 3.8.8
Posted: Fri Feb 25, 2022 11:56 am
by jeffx
Hondata wrote: Mon Feb 21, 2022 5:14 pm
V3.8.8 (21 Feb 2022)
- Firmware updated to version 208
- [FK2] Added idle fuel pressure, flex fuel support, traction control, full throttle shift and anti-lag.
- [FK8] Added fuel pump PID and feed forward tables
Will there be some further details on the significance of the feed forward tables and other changes for FK8?
Re: FlashProManager 3.8.8
Posted: Fri Feb 25, 2022 5:10 pm
by Hondata
I do not think so. There were put in for people using other fuel pumps, and if you have worked with PID control and feed forward tables then they are fairly self explanatory. It's one thing describing the tables but I really don't want to get into training people on the PID/FF.
The broader issue is that we added support for the XDI pump without the user being able to change anything other then enabling the pump. This way we take ourselves out of the loop if there is a tuning problem with the pump (so far there have not been any problems that I know about). The tables will get copied into other tuning software but at some point looking after people using our software is more important.
Re: FlashProManager 3.8.8
Posted: Mon Feb 28, 2022 5:26 am
by KT7788
Hi guys
After i upload with the lastest software 3.8.8
My Fk2 cannot start up .
It show A, engine , CTBA , ding ding ding .....
So i retry again, now it cannot detect ECU.
Did it bricks the Ecu ?? Or the software have any bug ?
Re: FlashProManager 3.8.8
Posted: Mon Feb 28, 2022 7:20 am
by KT7788
Hi Guy
Software 3.8.8
Model : FK2
Add on , Anti-lag & Flat throttle Shift
After Flash in the files .
The ECU went into protection mode, cant start the car .
Prompt A, Engine , CTBA Logo ding ding ding .....
Try to flash , ECU in protection , Flashpro cannot even detect ECU.....
Everything unplug , switch off , locked the car , when for a break around 30 min
Came back , Thanks god .. the ECU is out of protection mode.
Able to flash in without the 2 feature anti-lag and FTS
The Fk2 is working again.
Is there some bug on the 2 features ?
Can you guys please look into it .
Re: FlashProManager 3.8.8
Posted: Mon Feb 28, 2022 8:24 am
by Hondata
Thanks, we will look into this. If you could post the calibration that caused the problem here it would help. Also sending feedback with the FlashPro plugged into the vehicle would help a lot too.
Re: FlashProManager 3.8.8
Posted: Mon Feb 28, 2022 8:49 pm
by jeffx
Hondata wrote: Fri Feb 25, 2022 5:10 pm
I do not think so. There were put in for people using other fuel pumps, and if you have worked with PID control and feed forward tables then they are fairly self explanatory. It's one thing describing the tables but I really don't want to get into training people on the PID/FF.
The broader issue is that we added support for the XDI pump without the user being able to change anything other then enabling the pump. This way we take ourselves out of the loop if there is a tuning problem with the pump (so far there have not been any problems that I know about). The tables will get copied into other tuning software but at some point looking after people using our software is more important.
Thank you, that is exactly what I was wanting to know.
Re: FlashProManager 3.8.8
Posted: Mon Feb 28, 2022 9:36 pm
by KT7788
Hondata wrote: Mon Feb 28, 2022 8:24 am
Thanks, we will look into this. If you could post the calibration that caused the problem here it would help. Also sending feedback with the FlashPro plugged into the vehicle would help a lot too.
Hi guys
Only 2 extra features were turn with the base map.
- antilag & FTS
After flash, ECU go into protection mode.
Cant start .
After 30min i able to flash back to without the 2 add ons.
https://youtu.be/6BJOvZbq4NI
Thanks
Re: FlashProManager 3.8.8
Posted: Wed Mar 02, 2022 5:41 am
by Bain
Hondata wrote: Fri Feb 25, 2022 5:10 pm
I do not think so. There were put in for people using other fuel pumps, and if you have worked with PID control and feed forward tables then they are fairly self explanatory. It's one thing describing the tables but I really don't want to get into training people on the PID/FF.
The broader issue is that we added support for the XDI pump without the user being able to change anything other then enabling the pump. This way we take ourselves out of the loop if there is a tuning problem with the pump (so far there have not been any problems that I know about). The tables will get copied into other tuning software but at some point looking after people using our software is more important.
This is some good info, thank you.
So you will be looking at the XDI pump to be added for the FK2 also?