Page 1 of 1
84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Thu Jun 16, 2011 12:23 am
by gt35rdanny
84.5mm b20vtec w/ rs machine 11.5 comp. itr pistons, b16 head p&p, itr cams ,edelbrock victor-x mani,70mm TB. need a calibration to drive it to my tuner thanks
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Thu Jun 16, 2011 12:27 am
by gt35rdanny
bump
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Thu Jun 16, 2011 11:12 am
by gt35rdanny
up
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Wed Jun 22, 2011 4:46 pm
by hpmx18
try this map out from a friends car
b20 block rs machin itr spec
stock vtec head just valve train
16trans
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Thu Jun 30, 2011 5:47 pm
by hpmx18
feedback greatly appreciated with all those downloads
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Fri Jul 01, 2011 5:03 pm
by Mr.Dc2
hpmx18 wrote:feedback greatly appreciated with all those downloads
couldnt even ran this map on my car, feels like the engine its mis-firing and about to stall out. but i love the other map you provided.
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Fri Jul 01, 2011 6:53 pm
by hpmx18
What's your compression
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Fri Jul 01, 2011 7:56 pm
by Mr.Dc2
hpmx18 wrote:What's your compression
10:1 its the compression
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Sat Jul 02, 2011 4:03 pm
by hpmx18
subtract 20% in colums 1-5 if its does even worse add 35% to colums 1-4
*** if you have a wideband on tha car you can adjust the fuel more easier
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Sun Jul 03, 2011 8:17 am
by Mr.Dc2
[quote="hpmx18"]subtract 20% in colums 1-5 if its does even worse add 35% to colums 1-4
*** if you have a wideband on tha car you can adjust the fuel more easier[/quote
I end up adding more fuel instead, to get it working. but still don't feel safe and ended up switching to the other maps u provided , since its more stable. i completely understand a tune its necessarily but cant afford that right now. once again thanks for the help
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Sun Jul 03, 2011 4:09 pm
by hpmx18
no problem at all just get to tha dyno first priority
Re: 84.5mm b20vtec 11.5 comp. calibration needed asap!!!!
Posted: Wed Aug 13, 2014 4:12 pm
by premo583
do you think this calibration will work with my setup
b20vtec 84.5mm
rs machine itr pistons
fully ported b16a head ferra valves
crower 2 cams and crower springs
edlebrock victor x w/70mm tb
plm RMF header
240cc injectors for now I have rdx410cc to install
I have been running it on the jdmb18c map from hondata but its not enough fuel