Looks good. We will move onto the 15* cam now with vtec at 4500. I lowered the limiter to 8200 to give you room for shifting at 8000 so you don't bang off it. So now keep making the same type of drive, with the the third gear WOT pull from 2500-8200. At least run it out 8000 so we can get good data to that point if you don't want to hit the 8200 limiter that is fine.
Basemap?
Re: Basemap?
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Sounds good to me! Gonna eat dinner really quickly then ill be out.EFICU wrote: Mon Jun 21, 2021 5:33 pm Looks good. We will move onto the 15* cam now with vtec at 4500. I lowered the limiter to 8200 to give you room for shifting at 8000 so you don't bang off it. So now keep making the same type of drive, with the the third gear WOT pull from 2500-8200. At least run it out 8000 so we can get good data to that point if you don't want to hit the 8200 limiter that is fine.
Dinder.SD. Rev04 (15Cam)(Vtec4500).fpcal
Re: Basemap?
Hey! sorry that took a bit, tornado hit us pretty bad yesterday so there's a lot of traffic and closed roads haha. Since its getting a bit late just let me know whenever you're headed off, I'm free all week so whenever works best for you!
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
I'm in California so it's early, haha. We can go as long as you want. Two more revisions and we start to blend everything out. So it's totally up to you.
Here is the next one, 30* cam now with vtec at 4500 still. Same drive and everything like the last ones with the WOT pull in third.
Here is the next one, 30* cam now with vtec at 4500 still. Same drive and everything like the last ones with the WOT pull in third.
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Cool, should be able to get most of it done tonight then, ill be on my way out now,EFICU wrote: Mon Jun 21, 2021 7:08 pm I'm in California so it's early, haha. We can go as long as you want. Two more revisions and we start to blend everything out. So it's totally up to you.
Here is the next one, 30* cam now with vtec at 4500 still. Same drive and everything like the last ones with the WOT pull in third.
Dinder.SD. Rev05 (30Cam)(Vtec4500).fpcal
Re: Basemap?
EFICU wrote: Mon Jun 21, 2021 7:08 pm I'm in California so it's early, haha. We can go as long as you want. Two more revisions and we start to blend everything out. So it's totally up to you.
Here is the next one, 30* cam now with vtec at 4500 still. Same drive and everything like the last ones with the WOT pull in third.
Dinder.SD. Rev05 (30Cam)(Vtec4500).fpcal
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Looks good, here is the next one. 40* cam this time, this might be the last cam angle lock we do. The next one after this will be the start of fine tuning everything and your glimpse at how it will feel.
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Should be 2 third gear pulls in there, wasn't sure if it got to 8k on the first but made sure on the second.EFICU wrote: Mon Jun 21, 2021 7:55 pm Looks good, here is the next one. 40* cam this time, this might be the last cam angle lock we do. The next one after this will be the start of fine tuning everything and your glimpse at how it will feel.
Dinder.SD. Rev06 (40Cam)(Vtec4500).fpcal
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Looks good again. So here is the first one with the cam angles and everything blended out. Take it for a drive and see what you think. Feel free to drive it however you want, just be sure to get a clean third gear WOT pull like you have been. Other than that, feel free to get drive however you'd like. Then we'll see how it looks in the datalog. Vtec looks to be happiest around 4600, so see what you think about the crossover point there.
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Felt amazing! very new experience hahaEFICU wrote: Mon Jun 21, 2021 9:02 pm Looks good again. So here is the first one with the cam angles and everything blended out. Take it for a drive and see what you think. Feel free to drive it however you want, just be sure to get a clean third gear WOT pull like you have been. Other than that, feel free to get drive however you'd like. Then we'll see how it looks in the datalog. Vtec looks to be happiest around 4600, so see what you think about the crossover point there.
Dinder.SD. Rev07 (Blended).fpcal
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
Man that looked good for the first blended one. Part throttle fuel looks great, made a couple small changes to that and the WOT fueling. Overall it looks great, maybe one or two more revisions and it will be dialed. Glad you're happy with it, looks like it pulls pretty good for your setup for sure.
Here is the next one. I have time for more if you want, if it's late for you it's plenty good to drive anywhere you want. So it doesn't need any work to drive it as is, I'm just nitpicking stuff at this point now. If you want to resume tomorrow that's cool, if you want to keep going tonight that works too, totally up to you.
Here is the next one. I have time for more if you want, if it's late for you it's plenty good to drive anywhere you want. So it doesn't need any work to drive it as is, I'm just nitpicking stuff at this point now. If you want to resume tomorrow that's cool, if you want to keep going tonight that works too, totally up to you.
You do not have the required permissions to view the files attached to this post.
Re: Basemap?
I can go for one more right now, if it needs another revision after we can finish that up tomorrow whenever you're free!EFICU wrote: Mon Jun 21, 2021 9:51 pm Man that looked good for the first blended one. Part throttle fuel looks great, made a couple small changes to that and the WOT fueling. Overall it looks great, maybe one or two more revisions and it will be dialed. Glad you're happy with it, looks like it pulls pretty good for your setup for sure.
Here is the next one. I have time for more if you want, if it's late for you it's plenty good to drive anywhere you want. So it doesn't need any work to drive it as is, I'm just nitpicking stuff at this point now. If you want to resume tomorrow that's cool, if you want to keep going tonight that works too, totally up to you.
Dinder.SD. Rev08 (Blended).fpcal
Re: Basemap?
Sounds good. I always like you guys to make datalogs over the next few days after we call it good to make sure it's consistent over multiple days and everything is good. So yeah, take it for a spin, we'll see how it looks and then go from there. It's 99% dialed after this one I'm sure, my OCD kicks in sometimes and I nitpick little percentages for my own sanity. Haha.
Re: Basemap?
Sounds good I can do that, doesn't have to be perfect for me so no worries! Heres last one of the night (and maybe last one in general), Overall it was perfect and pulls good!EFICU wrote: Mon Jun 21, 2021 9:57 pm Sounds good. I always like you guys to make datalogs over the next few days after we call it good to make sure it's consistent over multiple days and everything is good. So yeah, take it for a spin, we'll see how it looks and then go from there. It's 99% dialed after this one I'm sure, my OCD kicks in sometimes and I nitpick little percentages for my own sanity. Haha.
You do not have the required permissions to view the files attached to this post.