Hondata

Improve Lambda Overlay Tooltip and other information

• Tooltip is always active if change by keyboard shortcut, for example Shift+F3, Tooltip visible, Shift+F2, Tooltip stuck;

• Add in the tooltip information like: Sensor Overlay, Fuel Cell Value, Ignition Cell Value and Cam Value;

• Add tooltips for other tables, minimizing changing table or changing cam tables;

• Place the tooltip in Ignition and Cam tables;

• Possibility to add to the tooltip more sensors;

• Ability to calculate Overlay Data from a folder of datalogs and not only use the current datalog;

Tables that are in use

• Add some indication on the cells in the tables of the Calibration that the value selected is being used, or select only the tables that are in use.
  For example: Some tables are with the cells selected, but the conditions to use that table aren't meted...
  Low Cam and High Cam values selected, another example: WOT tables selected and conditions aren't meted.

Power Button enable Function
Use the start button to display a certain sensor in the revs and parameterizable on the map.
This button can work in the same way as the Cruise Control button to read the Lambda, allowing the applicability of the function in more vehicles and making it possible to choose more sensors.
It only works after the vehicle is running and pressing the button again would activate or deactivate the function.

It can also be used to place another map that is in memory or a specific parameter (ON/OFF) while engine is running.

Im also requesting the FK2 downshift Rev match - i know lots of people who are interested in that feature!

Real-time Graph in Display
Ability to add a new control to Display in order to show the graph in real-time.
Or choose a Graph Template as new control in Display.

FK2 downshift Rev match

Please ! lets us enjoy this feature like the FK8.........

Please

In the FlashPro -> Datalogging -> a (New Button) "Save All" .
This option will Save the all the Datalogs and use the Directory and parameters in Settings under Datalog.

For FL5
The ability to DIASABLE second coolant temperature sensor (ECT2) for radiator fan control.
So it uses ECT to control the radiator fans.

Need similar options just like what is there for the FK8's

I am after a MIL light output for my build.
I am using an aftermarket dash (non honda). Would I be able to get a dissused output of my ecu to control a led MIL light.
I have an 37820-rbb-a71 ecu from an AT TSX.
I am using this in a Locost (Lotus 7 clone) which is using the K24a2 and an NB MX5(miata) 5 speed manual gearbox.
I will be using a flex sensor (so oxy sensor 2 input is being used), as well as the traction control module.
Maybe it would be best to use one of the disused AT outputs?

Any help would be great

Regards

Simon

Downshift Rev match and Multi-tune for Si, FN2, FK2.

Add Multi-tune options:

• Limit VSS - Enable to restrict speed. In this way implementing Valet Parking and Speed limits;

• Rev Limit - Implementing similar to speed, but by Rev;

• Throttle Limit - Implement cut off throttle at specific rpm, in this way able to press all the way the pedal and achive certain rpm points;

• Throttle Sensitivity - Adjust throttle sensitivity in a percentage, in this way add various stages of sensitivity;

Allow to change on-the-fly the presets in the Multi-tune, indicating by a light in Dashboard (edit mode) that the current value is about to be set.
After confirming the light should go off (view mode).

Keep up the good work.
Thanks.

add misc. parameter to disable auto stop/start option for US calibrations

For 2018 Accord 2.0T AT
1) radiator fan option
2) VTS option like the 2021 Accord 2.0T AT has
3) bring back the ECT Ethanol crank option back

2009-2015 Honda Civic Si (equipped with Drive By Wire Throttle)
Downshifts throttle rev match / Throttle auto blip
Please 🙏🏽

Nitrous control, please.

Please add radiator fan control for 2018+ Honda Accord, civic has it why can't Accord have it as well?

Please provide pop and bang funtion for FK2 and FK8