Hondata

EFICU wrote: Sun Jul 25, 2021 11:18 am

Shanebuilt wrote: Sun Jul 25, 2021 11:02 am V9 log seemed good, got some cruising and some spirited driving in there with ac off this time lol

Alright, we might be there. That one looked really good. I made a couple small adjustments, nothing major. The compensation changes from the last revision helped it a lot. The intake temps were still warm, but nothing you can do really with the short ram. We just have to make the best of it. When you get to the cooler months, it will really wake up.

Do you have their short ram that goes back towards the back of the engine, or the one that goes forward behind the headlight?

Here is the next one, we'll see how it looks. We might be there!

Shanebuilt.SD.Rev10 (Blended)(Vtec4300).fpcal

EFICU wrote: Sun Jul 25, 2021 11:18 am

Shanebuilt wrote: Sun Jul 25, 2021 11:02 am V9 log seemed good, got some cruising and some spirited driving in there with ac off this time lol

Alright, we might be there. That one looked really good. I made a couple small adjustments, nothing major. The compensation changes from the last revision helped it a lot. The intake temps were still warm, but nothing you can do really with the short ram. We just have to make the best of it. When you get to the cooler months, it will really wake up.

Do you have their short ram that goes back towards the back of the engine, or the one that goes forward behind the headlight?

Here is the next one, we'll see how it looks. We might be there!

Shanebuilt.SD.Rev10 (Blended)(Vtec4300).fpcal

Shanebuilt wrote: Sun Jul 25, 2021 12:18 pm Got V10 for you! some crusing, wot 3rd gear pull, and some spirited driving

EFICU wrote: Sun Jul 25, 2021 1:09 pm

Shanebuilt wrote: Sun Jul 25, 2021 12:18 pm Got V10 for you! some crusing, wot 3rd gear pull, and some spirited driving

Looks really good. Those changes worked well, everything looks good. I made tiny fuel adjustment in the final version. If yuou're happy with it, it looks good to go. I would still like for you to make a datalog on Tuesday and another one on Friday if you don't mind. I like to make sure it's good to go over multiple days to make sure everything is consistent. Use Rev11 moving forward, and send me the datalogs when you make them this coming week. If possible, in those datalog, make your normal third gear pull and also a pull or two in fourth gear from 3000-6000rpm so we can make sure it doesn't knock in fourth gear.

I also ran your best run through the Virtual Dyno in case you were curious at all. I'll attach the chart below. Take it with a grain of salt, could be a little high, could be a little low, it's just a vague reference. A video on YouTube shows similar mods making 197hp and 169tq, so we should be fairly close to that with your chart showing 191hp 165tq. With a DP for sure though it would pick up with some tuning modifications. So if you do add a DP, or go with a different intake, some changes would be needed to take advantage of those two things. But it's an easy clean up if you ever want help with it. Sorry we couldn't get more out of it, there is only so much we can do with the IATs as high as they are.

Shanebuilt Virtual Dyno.jpg

EFICU wrote: Sun Jul 25, 2021 2:59 pm Looks good. We'll see what it looks like in cooler weather if you're able to make a datalog then.

EFICU wrote: Sun Jul 25, 2021 2:59 pm Looks good. We'll see what it looks like in cooler weather if you're able to make a datalog then.

EFICU wrote: Fri Feb 11, 2022 3:45 pm Can you give me some more info on the new setup, seems as though the part throttle trims have gone a little rich, but the WOT fueling isn't too far off. Let me know a little more about what you did the the intake and the car delete, is it a DP or just deleted the cat?

EFICU wrote: Fri Feb 11, 2022 10:58 pm Okay. Yeah I went in and made a few adjustments, go ahead and take this one for a spin when you can and we will see how it looks. I also made a few other changes around the file to catch up to some of the things I do now.

Shanebuilt.SD.Rev12 (Blended)(Vtec4300).fpcal

EFICU wrote: Sat Feb 12, 2022 1:54 pm Looks pretty good. The fuel stuff is just about dead on. I made some changes for the knock. Give this one a drive when you can.

Shanebuilt.SD.Rev13 (Blended)(Vtec4300).fpcal

EFICU wrote: Wed Apr 27, 2022 9:27 pm Unfortunately no, it will need a complete retune as the RBC changes everything in the tune. I'll have to put together a starting file for you and go back through everything. Are you still thinking about adding a DP?

When are you planning to install the RBC?