Hondata

Hondata wrote:

VitViper wrote:Yes... I had one come into the shop last month, had a discussion with Doug about it... the ECU is "R9B-A03", which is listed as supported in the 1.6.3 update:
[ILX] Added support for the R9B-A03 ECU
However that's not the case -- FlashPro refuses to recognize the ecu and will not lock/flash the car. We were told this would get fixed in the "next beta". :/
We even had him send support info like 4 weeks ago, per Doug's request.

Yes, we added the binary R9B-A03 in 1.6.3 but the problem you had was related to the ECU part number. It should work now.

I suspect as much -- we'll try 1.8 on it and see how it goes.

Hondata wrote: So you want misfire disable on the 06 Civic? We'll add it in.

Absolutely, it's been a problem with the 06-11 Civic calibrations for months -- I cannot use any very large injector without triggering a million codes.

R-12914 wrote:

Spunkster wrote:what error are you getting?

If i try this:
1. Plug the FlashPro into the diagnostic connector and switch on the vehicle ignition.

· Primary calibration - press the Program button for at least one second.
· Secondary calibration - holding the Datalog button down, press the Program button for at least one second, releasing the Program button before the Datalog button."

Than the FlashPro does nothing!

I have also upload the Cals again from the Notebook to the Flashpro and than from the Flashpro to the ECU, but the same as before! :(

Yes！I also got this problem...

MJz wrote: Yes！I also got this problem...

What car do you have?

@Hondata: When will the problem be fixed?

@Hondata: When will the problem be fixed?

I've narrowed it down. It only affects FlashPros without Bluetooth. It will be fixed and a release made in the next few hours.

Hondata wrote:V1.7.3 (2 Apr 2014)

• FlashPro firmware updated to version 61
• Bluetooth enabled
• [07-08 TSX] Added ability to program AT ECU with MT program
• [TL] Added ability to program AT ECU with MT program, only base model ECU (RDA-A85)
• [2006 R18 MT Civic] Added support for the RNA-A150 calibration.
• [CR-Z] Fixed misfire code disable.

V1.8.0 (3 Apr 2014)

• FlashPro firmware updated to version 62
• Fixed Bluetooth detection

Download here

just wonder if the link to 1.8.0 was removed? for some reason I get a error and it states "not found" also I have tried updating thru flashpro manager and It keeps stating programing is not a 32 bit program and closes down. just wondering if anyone else is having this issue?

It is because we are in the process of doing an update.

Shift + F1 once again is back to opening the help file instead of showing the normal fuel tables... ugh :(

R-12914 wrote:

MJz wrote: Yes！I also got this problem...

What car do you have?

@Hondata: When will the problem be fixed?

My one is Civic ABA-FD2 Type R。

Bug is fixed - THX! :)

Thank you for the Civic cal misfire detection toggle.

I read the flash pro help file.

V1.8.1 (4 Apr 2014)
• FlashPro firmware updated to version 63
• Bluetooth enabled
• [2012+ Civic] Added support for RX0-K020 through RX0-K060
• [07-08 TSX] Added ability to program AT ECU with MT program
• [TL] Added ability to program AT ECU with MT program, only base model ECU (RDA-A85)
• [2006 R18 MT Civic] Added support for the RNA-A150 calibration.
• [CR-Z] Fixed misfire code disable.
• [CRZ-Z] Added support for RTW-H510 and RTW-U510

May I know does it mean FlashPro is now supported ECU part number RTW-U51? Any different between RTW-U510 and RTW-U51?

Thank you,

The 3 digit codes are part numbers (RTW-U51) and the 4 digit codes are calibration IDs (RTW-U510).

Hondata wrote:The 3 digit codes are part numbers (RTW-U51) and the 4 digit codes are calibration IDs (RTW-U510).

Does it mean version v1.8 is now supported ECU code RTW-U51? Asian First Generation CVT CRZ?

Thanks!
Terence

I'm having the non bluetooth version of the flashpro. The latest firmware seemed to have fixed the button issue.

But now the flashpro doesn't turn on/turn off itself (no lights) when there is no activity and cannot datalog/program.

I have to unplug the obd and replug it in before it works.

terenceng wrote:Does it mean version v1.8 is now supported ECU code RTW-U51? Asian First Generation CVT CRZ?

It should do. The problem is that we can't tell 100% what calibration is in each ECU from the part number.