Page 8 of 23
Re: SManager software requests
Posted: Tue Mar 13, 2012 7:49 am
by Johnny_9
Tip-in trim by rpm, +% and decay rate. Really need this.
Re: SManager software requests
Posted: Tue Mar 13, 2012 8:10 am
by Johnny_9
OBD1 to OBD2 protocol converter
Re: SManager software requests
Posted: Thu Mar 15, 2012 2:41 am
by Johnny_9
Need a much better compare calibration function.
Re: SManager software requests
Posted: Thu Mar 22, 2012 11:44 am
by Amon
I would like to see a detailed history function so I can see what I did previously.
No help on tip-in fuel v ECT
Posted: Fri Mar 23, 2012 6:16 am
by Johnny_9
?
Re: SManager software requests
Posted: Sat Mar 24, 2012 4:38 am
by portenio78
Stock d16y8 calibration.
Re: SManager software requests
Posted: Thu Apr 05, 2012 6:24 am
by Johnny_9
serial output to log all ECU parameters.
Re: SManager software requests
Posted: Fri Apr 13, 2012 7:10 pm
by FreshDA9
Hows about a pressure vs duty cycle table based on map sensor selection. under boost control parameters. having more cells will allow better adjusting for desired psi.
live logging in the battery offset tables will help will help a lot, also logging of anything in the parameters tab!
Another option for widband logging. Being able to log only a selected gear. this will clean up a lot of Overrun when on dyno or street. Just be able to make a check box for N-5 gear also stop logging on fuel cut.
Hows about serial logging support for widebands. no more playing with voltage offsets just put your usb in and select your port and go.
Custom target AFR for whole map, not just 3 columns.
above are some old request.
Would also be nice to remove the 2D/3D graph simple button click.
Re: SManager software requests
Posted: Thu Apr 26, 2012 7:23 pm
by portenio78
Overlay 2 log graphs over eachother?
Re: SManager software requests
Posted: Sun May 06, 2012 9:50 am
by joeb
I know this has come up before . It would be fantastic if we could use the knock sensor and log knock properly . I see this feature with the dsm guys and it is invaluable .
Re: SManager software requests
Posted: Sun May 06, 2012 4:53 pm
by Hondata
The knock logic is handled completely by the knock daughter board. The only interface is a suggested knock retard, which is what's datalogged.
Re: SManager software requests
Posted: Thu May 10, 2012 4:49 pm
by kerndog
I would like to have 2 seperate boost cuts---one for primary and secondary tables, or linked to the low and high boost tables? I'm going to push it a little and ask for 2 quick spool tables as well, and have it possible to set them to the same switch that changes to secondary tables similar as the low and high boost.
Re: SManager software requests
Posted: Sun May 13, 2012 5:53 pm
by SPOOLIN
check box to make launch limiter/anti lag override the activated burn out rev limiter.
once it gets past its set mph it will then use the burn out rev limiter.
this way your not trying to start turning over slicks with 6 psi in them from a dead rev limiter with no power behind it.
Re: SManager software requests
Posted: Mon May 28, 2012 11:14 am
by ITR1102
I like the red cell trace line that is used in KManager. That really helps me see where I am at in each cell while live tuning (street tuning). Is this possible to incorporate into SManager?
Injector dead time vs Fuel Pressure
Posted: Sat Jun 09, 2012 9:19 pm
by Johnny_9
Injector dead time vs Fuel Pressure/Volts.