P0010

himsweet66six · Post by **himsweet66six** » Fri Jul 06, 2012 8:09 pm

ok here is the run down of my problem. current setup. 05 type s with full k24a2 swap. previously i was using a kpro prc ecu with the 05 jumper harness. car ran fine and never threw this code. i recently swapped my ecu for a kpro prb ecu. everything seems to run fine but when i give it gas it throws the p0010 code. i just bought a brand new vtc solenoid hoping it would fix the problem but it threw the same code again. i am not sure what is happening or how to fix this. does anyone have any insight?

Post by **Spunkster** » Mon Jul 09, 2012 10:19 am

What is the serial number of the K-Pro board inside the ECU?

himsweet66six · Post by **himsweet66six** » Mon Jul 09, 2012 6:02 pm

Spunkster wrote:What is the serial number of the K-Pro board inside the ECU?

05003782

Post by **Spunkster** » Tue Jul 10, 2012 9:20 am

This ECU is not designed for running with an adapter harness. The 05-06 adapter harness is only for use in an 05-06 RSX and is not for use with engine swaps.

himsweet66six · Post by **himsweet66six** » Tue Jul 10, 2012 10:31 am

Ok so how can I get this to work? Can I ground the vtc(-) to the chassis or run a wire to splice into the correct wire on the harness?

Post by **Spunkster** » Tue Jul 10, 2012 1:16 pm

The ECU would have to be sent in to be upgraded to work in an 05-06 RSX. The cost for this is $250. You would have to fill out the K-Pro form and note what it is you want done and include a cashier's check for the full amount.

himsweet66six · Post by **himsweet66six** » Tue Jul 10, 2012 5:05 pm

Spunkster wrote:The ECU would have to be sent in to be upgraded to work in an 05-06 RSX. The cost for this is $250. You would have to fill out the K-Pro form and note what it is you want done and include a cashier's check for the full amount.

so its not possible to just ground out the sensor? I dont understand how my kpro prc ecu was able to run fine.

Post by **Spunkster** » Wed Jul 11, 2012 4:04 pm

No the only solution is what I mentioned above.

himsweet66six · Post by **himsweet66six** » Wed Jul 11, 2012 4:57 pm

Spunkster wrote:No the only solution is what I mentioned above.

ok well i have an eps setup in my car with a dakota speed converter will this be affected if i do this upgrade?

himsweet66six · Post by **himsweet66six** » Mon Jul 16, 2012 11:36 am

I looked at the form and was confused as to who i should send my ecu to. do i send it directly to hondata? also do i just state that i need the ecu to be compatible with an 05 rsx type s with a k24a2 swap? let me know so i can send this out.

Post by **Spunkster** » Mon Jul 16, 2012 4:26 pm

Fill out the from at http://www.hondata.com/kproecuinfoform.html

Choose the option for the 05-06 K-Pro. Y0u must include a cashier's check for $250

himsweet66six · Post by **himsweet66six** » Tue Aug 14, 2012 9:08 am

just got my ecu back. also came with a 05-06 wiring harness. now i already have an 05-06 harness, but i need to know if there is any differance between my older harness and the new one i just received. thanks in advance for the response.

Post by **Spunkster** » Tue Aug 14, 2012 10:54 am

The other harness may have been counterfeit.

Hondata

P0010

P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010

Re: P0010