need an advice

ali hussain · Post by **ali hussain** » Wed Nov 03, 2010 9:52 am

we want to change our engine wiring harness its obd0 right now so what do you advice me to install obd1 is better or obd2 because we want also to install hondata p28 ecu and the engine is b16 turbo so can anyone help me??

Post by **Spunkster** » Wed Nov 03, 2010 9:57 am

http://www.hondata.com/techobd0conversion.html

ali hussain · Post by **ali hussain** » Wed Nov 03, 2010 10:47 am

my friend i want to change the full wiring i dont want to convert my wiring so which is better obd1 or obd2 and where can i find it like on which website is it available?

Post by **Spunkster** » Wed Nov 03, 2010 10:56 am

I would suggest contacting Hasport

ali hussain · Post by **ali hussain** » Wed Nov 03, 2010 11:09 am

and how can i be in a contact with them?

Luke · Post by **Luke** » Wed Nov 03, 2010 11:21 am

change your wiring completly to OBD1, that you can just wire an OBD1 ECU to it and tune it.

the wiring itself you could get from any honda OBD1 model as EG5/EG6 or similar.

that should work quite well, إن شاء الله‎

best regards Lukas

ali hussain · Post by **ali hussain** » Wed Nov 03, 2010 11:31 am

hey thanx friend thats what i was really waiting for this is what i wanted to know and إن شاء الله it will work well and can i plug the hondata p28 ecu ? because that is what we are planning to install

Luke · Post by **Luke** » Wed Nov 03, 2010 2:59 pm

if you swap your OBD0 wiring to OBD1, then you just plug-in the ECU (P28/30/72), chip it first and add the S300. that should work.

but, for sure, make some photos of the car, the wiring and ECU.

it is unbelievable, that honda puts in other wiring into some cars in the middle east?! that would cost so much, that it wasn't rentable.

let us recheck it, before you look for a new wiring harness. photos will help a lot.

best regards Lukas

ali hussain · Post by **ali hussain** » Sat Nov 06, 2010 4:28 am

my friend we haven't take out the wiring still so do you want to see it and its in the car and we did not get the obd1 wiring so can you tell me exactly how do you want to see the wiring so that i can capture the photos for you and i know that it is going to cost so much but we are planning to build a strong car that's why we will try our best by the help of you guyz and your advices ;) thanx alot

Luke · Post by **Luke** » Sat Nov 06, 2010 6:41 am

ECU connectors would be great, the distributor... that should be ok.

as far as I know, the OBD0 were not produced anymore after 1990.

best regards Lukas

ali hussain · Post by **ali hussain** » Sun Nov 07, 2010 5:39 am

the car is actually honda prelude 1983 and the wiring is honda integra 1993 wiring and its obd1 but i will get the the photos and show you

Luke · Post by **Luke** » Sun Nov 07, 2010 9:52 am

if the whole wiring is OBD1, then it's great. just put a chipped P28/30/72 in with the S300, get it tuned and everything is alright.

what are your plan, in fact?
this engine shall be in that car? turbo? supercharged? N/A? what are the plan.

if i had money i would go to bahrain for some holiday and could help you :D
and check the new F1 course by the way :D

best regards Lukas

ali hussain · Post by **ali hussain** » Tue Nov 09, 2010 6:24 am

hahah that will be really nice to have a racer friend :P actually the engine is almost ready it's a b16 turbo with 650cc injectors with some extra additions but if you are serious come to bahrain and i will be really happy to welcome you :D and you will enjoy our street races as there are alot of honda'z here "honda the best :D" we are searching now for a good wiring harness

Luke · Post by **Luke** » Tue Nov 09, 2010 6:56 am

i'd like to come to the middle east, too.

but now it's impossible. i'm still university student, have no money to go around the world :D

don't you have you own oil well there with a lot of oil-dollars?? :D

there is also a direct flight to bahrain from a near airport :D

best regards Lukas

ali hussain · Post by **ali hussain** » Tue Nov 09, 2010 6:59 am

hahaha i hope that i can find this oil well which you are talking about so that i can make the worlds fastest honda hhahaha but i am a university student too and an engineering student but hope to see you some day lol add me if you like
ali.alyas@hotmail.com
ttyl , c yaa