kpro help needed

leetec · Post by **leetec** » Wed May 05, 2010 3:47 pm

hi noob here located in scotland. im havin a problem with openin the map for my car in k manager an error message pops up sayin
"list index out of bounds (0)" laptop hasnt been pluged into car when this was happenin but didnt think that would make much difference?
anyone had this before? thanks lee

Post by **Hondata** » Thu May 06, 2010 8:21 am

Download and update KManager. If this error occurs, can you tell us when it happens? If possible, provide a screen shot as well.

leetec · Post by **leetec** » Thu May 06, 2010 3:51 pm

the kmanager is upto date. i have come home from work ad opened the map and no error code now. why would this be? i tried to upload it to the ecu but it doesnt seem to be workin. by this i mean i have got the map clicked upload.......the little box opens up sayin uploadin.....then when the scale reaches the end box disapears..... i thought it would have been loaded but it is still runnin on the previous map that was on the ecu. any advise would be much appreciated. am i doin something wrong?

Post by **Spunkster** » Thu May 06, 2010 5:06 pm

How long did it take to upload the calibration to the ECU?

leetec · Post by **leetec** » Fri May 07, 2010 9:52 am

Spunkster wrote:How long did it take to upload the calibration to the ECU?

it doesnt take that long........maybe around a minute. is that about right? is their meant to be a message sayin upload complete after map has been succefully uploaded?

Post by **Spunkster** » Fri May 07, 2010 10:34 am

No, there is no message when it finishes. It sounds like it is working correctly.

leetec · Post by **leetec** » Fri May 07, 2010 11:45 am

thats what i thought.
ok just been playin around with the kpro their and here is whats happening.
i have saved the map for my car twice the only difference between the 2 maps is 1 has launch control+dataloging enabled and the other doesnt.

map 1 has NO launch control+dataloging enabled
map 2 has launch control+dataloging enabled

when openin map 1 this is when this is when "list index out of bounds" error occurs

when i open map 2 the map opens fine and seems to upload to ecu no problem. switched ignition and car off closed k-manager. opened k-manager and tried to down load map from ecu when the error message "please check all calibration parameters for accuracy. in order to ensurethat the binary code is upto date please save the calibration and then upload to the ecu" appeared
i clicked ok and the map that came off of ecu was a previous map i put on just to get the car started.
so why would it not be loadin my map?

i tried to update the USB drivers and got an error message sayin "error updatin USB driver(error access is denied.)

im not havin much luck as you can see........i was really looking to have car at local 1/4mile in 2 days so any feed back is much appreciated. thanks lee

Post by **Spunkster** » Fri May 07, 2010 12:08 pm

post the calibrations in question

leetec · Post by **leetec** » Fri May 07, 2010 12:12 pm

Spunkster wrote:post the calibrations in question

here you are. let me know what you think.

Post by **Spunkster** » Fri May 07, 2010 12:53 pm

310bhp map.kal is corrupt and you will have to just use the other calibration and make the necessary changes to it.

leetec · Post by **leetec** » Fri May 07, 2010 12:55 pm

Spunkster wrote:310bhp map.kal is corrupt and you will have to just use the other calibration and make the necessary changes to it.

leetec · Post by **leetec** » Fri May 07, 2010 1:00 pm

Spunkster wrote:310bhp map.kal is corrupt and you will have to just use the other calibration and make the necessary changes to it.

How can the 310bhp map.kal be corrupt and the map not because is a copy so surely both should be corrupt????
What is the necessary adjustment needed?? Do you know why the map would not go onto the ecu? I appreciate your help spunkster

leetec · Post by **leetec** » Sat May 08, 2010 3:40 pm

can anyone else help? is their anyway of fixin the corrupt map?

Post by **Spunkster** » Mon May 10, 2010 9:19 am

It cannot be fixed. You will have to use the one that works and make your changes to that one.

leetec · Post by **leetec** » Tue May 11, 2010 4:31 pm

here is a couple of datalogs i done. can anyone tell me why the car was shuttin down at 10psi of boost? i know ithey are not the greatest but its the best i can do at the moment. thanks lee