where the hell is my ELD on my obd2b stock harness *CANADA*

migee · Post by **migee** » Sat Aug 22, 2009 5:28 pm

Hi guys,

I have the special edition s300 for integra 98-01 in my 2000 LS. It has the built in obd2b connector. Now im trying to finally get my wideband analog out to it, and I notice that there IS no eld wire in my harness. does obd2b not have one?

http://www.ff-squad.com/technet/wiring.obd2b.htm

here it says A30 but there is no such wire on my stock harness A connector... I see the brake switch A31 there, but no green/red wire next to it. Also... oddly, the 30 on the graphic of the harness is crossed out, and not given a number... why?

Where do I go from here?

edit: not sure if this matters, im in canada and its a 2000 integra SE (pretty much an ls)

fly_n · Post by **fly_n** » Sat Aug 22, 2009 9:43 pm

if your not using something like A/C,power steer,knock sensor,etc,etc then use that pin & repin it to A30 then u have wire to join onto.
if your not planning vtec than even those pins might be present in your harness & u can use one of those.
even go down the junkyard & find a spare pin with a bit of wire on a wreck,chop off the whole plug so u got heaps of spare pins even.
u might find a pin from any obd1+ honda plug will fit,just as long as its the smaller one of the 2 sizes.

migee · Post by **migee** » Sun Aug 23, 2009 6:12 am

fly_n Thanks!

I deleted my AC so I'll try to repin it to a30. I'm sure I can find an article on how to repin as I've heard of it being done many times before. Thanks again.

migee · Post by **migee** » Sun Aug 23, 2009 5:26 pm

Ugh problems.

A/C doesnt even match up with the obd2b pinout for my car. And of ALL the depinnings I've seen the obd2b connectors dont seem anything of the same.

Now I'm really confused on what to do.

I went looking for blue/red A/C switch on A27. Only A28 has a wire on that row, but its for A/T according to the pinout (im manual) and green.

fly_n · Post by **fly_n** » Sun Aug 23, 2009 5:42 pm

easy fixed,u r obd2a,check D16 for ELD

http://technet.ff-squad.com/wiring.obd2a.htm

migee · Post by **migee** » Sun Aug 23, 2009 5:43 pm

im not obd2a, im 2b. its a 2000, and I dont have d connector.

edit: damnit canada.

fly_n · Post by **fly_n** » Sun Aug 23, 2009 6:11 pm

is there a space next to the A-plug or is the B-plug right next to it?

migee · Post by **migee** » Sun Aug 23, 2009 6:25 pm

no space. have ABC, no D. Im sure its odb2b. just some canadian variant it seems . cant find anything abotu the differences from usdm to canadian.

fly_n · Post by **fly_n** » Sun Aug 23, 2009 6:38 pm

put up a pic of the plugs,or list a few more wire colours going to whatever pin numbers u think.

migee · Post by **migee** » Sun Aug 23, 2009 6:57 pm

thanks for the help. Ill do that , and ill see what matches and what doesnt.
will post when i get more time.

migee · Post by **migee** » Mon Aug 24, 2009 3:13 pm

I darkened those that I dont have, and made red what is different. Interesting.

But at least one of the A/C pins match up, I guess I can try stealing that one.

edit: Car came with p/s, cruise, a/c. Why some are missing *shrug*

migee · Post by **migee** » Wed Sep 02, 2009 4:02 pm

just an update. I have it working. I noticed after mapping out my pins that the a/c switch one is indeed there, as the last 8 pin numbers on that webpages diagram are not numbered correctly.

I was able to cut out that one, and move it over and splice it into my wideband and now ELD shows the right voltage, with no offset even.

thanks for the help fly_n

Hondata

where the hell is my ELD on my obd2b stock harness CANADA

where the hell is my ELD on my obd2b stock harness CANADA