need help....kpro issues

vivalive · Post by **vivalive** » Wed Mar 12, 2008 6:53 am

my Iat engine is on after installed kpro, and it lock my cams at 0 degree..
i need help fixing this issues.. could someone help me.. i've checked all the wiring and refered to the services manual..
k20a3 2005 model rsx.

Post by **Spunkster** » Wed Mar 12, 2008 10:21 am

Have you tried the ecu in another vehicle?

vivalive · Post by **vivalive** » Wed Mar 12, 2008 12:24 pm

no i havn't... my kpro is brand new shouldn't there be no problem?
by the way. its a type-s ecu k-kpro.

vivalive · Post by **vivalive** » Wed Mar 12, 2008 12:26 pm

Spunkster wrote:Have you tried the ecu in another vehicle?

does the type-s and base rsx share the same sensor on the throttle body?
i know the throttle body is different but not sure about the sensor?

Post by **Spunkster** » Wed Mar 12, 2008 4:50 pm

The sensors are all the same. Please try the ecu on another vehicle. This will tell you if it is a problem with your ecu or with your car.

vivalive · Post by **vivalive** » Wed Mar 12, 2008 5:25 pm

Spunkster wrote:The sensors are all the same. Please try the ecu on another vehicle. This will tell you if it is a problem with your ecu or with your car.

will i have check engine if i ran my stock 2005 ecu with 2004 o2 sensor?

Post by **Spunkster** » Thu Mar 13, 2008 9:36 am

You have asked this before. You must use the 02-04 o2 sensor with the K-Pro. You are trignto determine if there is a problem with the IAT, so don't worry about other errors when testing. Just look for the IAT error.

vivalive · Post by **vivalive** » Thu Mar 13, 2008 11:27 am

Spunkster wrote:You have asked this before. You must use the 02-04 o2 sensor with the K-Pro. You are trignto determine if there is a problem with the IAT, so don't worry about other errors when testing. Just look for the IAT error.

i've change the 1st o2 sensor, do i need to change the o2 after the cat?

Post by **Spunkster** » Thu Mar 13, 2008 2:35 pm

vivalive · Post by **vivalive** » Thu Mar 13, 2008 3:39 pm

when i unplug my IAT kpro is still throwing " IAT LOW VOLTAGE" and the temperature reading is the same 95f.
what should i do? my turbo kit is comming in next week... i want to get this fixed. i don't want to use Emange!

type-s ecu/ 05 base rsx.

vivalive · Post by **vivalive** » Thu Mar 13, 2008 4:03 pm

could i only buy a new harness?

Post by **Spunkster** » Thu Mar 13, 2008 4:57 pm

There is no need to buy a harness since you have not completed all the troubleshooting steps yet. You need to try this ecu in another vehicle to see if it is getting the same IAT error there.

vivalive · Post by **vivalive** » Thu Mar 13, 2008 6:25 pm

Spunkster wrote:There is no need to buy a harness since you have not completed all the troubleshooting steps yet. You need to try this ecu in another vehicle to see if it is getting the same IAT error there.

there isn't another 05-06 rsx i could try on.... could i try it on an 02-04?

Post by **Spunkster** » Fri Mar 14, 2008 9:32 am

Yes you can try it on any RSX, just don't use the adapter if it's an 02-04.

vivalive · Post by **vivalive** » Fri Mar 14, 2008 3:35 pm

Spunkster wrote:Yes you can try it on any RSX, just don't use the adapter if it's an 02-04.

today i took out my Iat, and figure out its cooked/melted. could there be a short somewhere?