Push button install question

mikeedge · Post by **mikeedge** » Tue Aug 15, 2006 11:49 am

I am currently tuned on Hondata S200. I am looking into installing my push button so I can control my rev limit, launch control, and shift light.

I have read on the Hondata installation guide that once installed... the rpm points are initially set to the following...

Launch Limiter: 3000rpm
Cam Change point: 4800rpm
Shift limiter: 6000rpm
Shift light: 7800rpm

Now my question is... my vtec crossover is set right now to 4400rpms. Once I install this, is it going to switch it to 4800rpm? and am I going to have to reset it back to 4400rpm?

Thanks for any help.

Post by **Spunkster** » Tue Aug 15, 2006 11:53 am

If VTEC has been set in the ecu it cannot be adjusted via the interface box.

mikeedge · Post by **mikeedge** » Tue Aug 15, 2006 12:21 pm

Okay, so I don't have to worry about my crossover going to 4,800rpm?

mikeedge · Post by **mikeedge** » Tue Aug 15, 2006 12:59 pm

Okay, I plugged the push button in and set my launch control rpms to 2,500 statically. I turn my car on and press the clutch in and when I step on the gas pedal, the launch control doesnt work, my rpms just rocket.

Any ideas why?

Post by **Spunkster** » Tue Aug 15, 2006 3:44 pm

Datalog and make sure that the ecu is seeing the clutch switch engaging and disengaging.

mikeedge · Post by **mikeedge** » Tue Aug 15, 2006 5:09 pm

Lol, I found out that I need the clutch switch. I was under the impression that I only needed the clutch switch for Full throttle shift.

Where should I get the clutch switch from? I have access to pepboys, advance autoparts, etc.

What are they called exactly?

mikeedge · Post by **mikeedge** » Tue Aug 15, 2006 6:45 pm

Okay, I went out to pepboys and bought a switch. Now my question is, How do I go about hooking it up to the Hondata?? It didn't come with any wires or anything.

Post by **Spunkster** » Wed Aug 16, 2006 10:04 am

http://www.hondata.com/featureslaunch.html

http://www.hondata.com/downloads/s200%2 ... manual.doc

mikeedge · Post by **mikeedge** » Wed Aug 16, 2006 1:43 pm

Lol, I looked through that manual so many times. It just does not say how to hooke up the clutch switch to the hondata.

I am fully aware of where to put the clutch switch, but just not how to hook it to the hondata.

Post by **Spunkster** » Wed Aug 16, 2006 3:22 pm

It plugs in on the interface box where it says "Clutch Switch"

mikeedge · Post by **mikeedge** » Wed Aug 16, 2006 4:35 pm

Lol, I am aware of that. But I do not have any wires that plug into that. The clutch switch I bought came with just a clutch switch. Here are some pics of it...

Post by **Spunkster** » Wed Aug 16, 2006 4:50 pm

Every s200 is shipped with the necessary cable to connect to the switch.

mikeedge · Post by **mikeedge** » Wed Aug 16, 2006 5:29 pm

Hmm, well I bought this from a member off Team-Integra so that could explain why I do not have the cable. I did have th push button tho.

How could I acquire one of these cables?!

Ps. Thanks a lot for all your help! I appreciate it.

Post by **Spunkster** » Thu Aug 17, 2006 9:15 am

You can purchase a replacement through any Hondata dealer.

mikeedge · Post by **mikeedge** » Thu Aug 17, 2006 10:14 am

Okay, is it just the cable? or the clutch switch as well?