K-Series Programmable ECU installation questions / support issues
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Mon Aug 31, 2020 9:15 am
Hi everyone,
Set up:
Kpro V3
2000 Integra Gsr w/ k20a2 swap
Hybrid Racing Conversion Harness
RSX Type S stock harness
Made all the connections needed for everything to work from the conversion harness to the RSX Type S engine harness.
ISSUE
[] When i plug the Kpro onto my laptop, and start 'datalogging' , most sensor readings are at ZERO
[] and according the Kpro, no error codes (which is weird to me)
[]For the systems under Error Codes, it also says not supported!
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Mon Aug 31, 2020 9:48 am
What is the serial number that is on the K-Pro board inside the ECU?
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Wed Sep 02, 2020 7:41 pm
Serial Number - Kpro 13175
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Thu Sep 03, 2020 9:06 am
When was the last time that this was working?
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Tue Sep 22, 2020 10:11 am
Spunkster wrote: Thu Sep 03, 2020 9:06 am
When was the last time that this was working?
Have you tried the ECU in a known working vehicle?
The K20a2 and the Hondata Kpro v3 we're taken both off a 2002 Acura RSX Type S. I drove the RSX for a couple of months no problem. Which is why I dont know why its not reading any sensors
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Tue Sep 22, 2020 10:31 am
the K20a2 + Hondata kpro is the swap set up i am using on my DC2 Integra
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Tue Sep 22, 2020 11:37 am
Have you uploaded a calibration to the ECU since updating the software?
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Tue Sep 22, 2020 1:33 pm
Spunkster wrote: Tue Sep 22, 2020 11:37 am
Have you uploaded a calibration to the ECU since updating the software?
Yes, I have. But I cant tell if it works since no sensor data appears when 'datalogging'
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Wed Sep 23, 2020 3:30 pm
IF you set an artificial rev limit of 2000 rpm, and upload the calibration, is there a rev limit at that RPM?
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Sun Sep 27, 2020 1:33 pm
Just tried this tune attached, and rev'd it (expecting to limit at 2k rpm) but it went past it
and this is what I see
stock.kal
You do not have the required permissions to view the files attached to this post.
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Mon Sep 28, 2020 9:21 am
It shows that it is online, but the ignition is off. You should try this ECU on a different vehicle and see if it shows that the ignition is on.
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Mon Sep 28, 2020 9:55 am
Spunkster wrote: Mon Sep 28, 2020 9:21 am
It shows that it is online, but the ignition is off. You should try this ECU on a different vehicle and see if it shows that the ignition is on.
This is what it says when the car is actually on
You do not have the required permissions to view the files attached to this post.
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Mon Sep 28, 2020 9:59 am
And for some reason, once turning off the car, I heard the ECU beep twice (1 min in between each beep) .
Spunkster
Site Admin
Posts: 23878 Joined: Fri Sep 20, 2002 5:06 pmLocation: Hondata
Post
by Spunkster Mon Sep 28, 2020 1:04 pm
Is this in a different vehicle?
Jonny7isa
Posts: 12 Joined: Mon Aug 24, 2020 9:27 am
Post
by Jonny7isa Mon Sep 28, 2020 1:08 pm
Spunkster wrote: Mon Sep 28, 2020 1:04 pm
Is this in a different vehicle?
Same vehicle
