Hondata

after i hung the phone up from talking to you last night, i went to find my multimeter and realized i had left it at my shop, (doing coil installation at home and figured it was a basical install and wouldnt need it) so i ran to run over and grab it, and when i got back, you guys were already closed ...

took pictures of the ecu, i purchased this ecu from you guys a few years back.. it has had the small sticker over the plugs removed, as well as the side one on the case, so i took pictures of the numbers on the actual board, shown in the photos.

the ecu was socketed by you guys, the case has the ...

i purchased a retro fit kit from a dealer, with an adaptor for k series coils, which i have completely installed to exact specs of the included manual. I did the sync on hondata, and when i went to fire the car up, it just turned over. so i diconnected the injectors, and then went threw the ...

I sorta understand what your saying. So the low side of the fuel table, i wouldnt need to change any of the values, but once i hit the high side of the fuel table, i need to change only the higher portion of the map, say 5000+..??

do the increments that change from index box to index box have to be ...

ive done that and it doesnt add any more columns, it just changes the number thats in that perticular box, unless done at the top of the map, where it adds one, but still doesnt have the fuel table higher then 8950.

If i was going to rev the car 9500, i would make the rpm index go to 10100. With 20 ...

I have a high compression b series, and went out to tune the car last night setting the rev limitor to 9400rpm. Making a pull to rev limitor, as i approaced 8900rpm i noticed the wideband on the graph flat line along with the timing. letting off, i checked the datalog and as i got to the end of the ...

im confused why your AF is reading .81.. the fuel looks smooth, but you need to change the settings on your AF from.7-1.7. to 10-20 on your graphs.. Click on AF on the sensors tab, and youll see on the bottom, Display Min, Display max. change those to 10 and 20.

You can just load a stock ITR or GSR map, and make a datalog, and post your calibration and datalog onto the forums here, and i bet there would be someone willing to make adjustments for you. Just be careful on it, as not everyone on here is a repuabale tuners, so its on your own if something ...

depending on how long you attempted to start that motor, your oil might have quite abit of gas in it. Also, if you try and start a motor for a while, you can wash the cylindor walls down, which requires a very small amount of oil to be poured down the spark plug hole to revive the cylindor walls ...

well today i did a few more datalogs and noticed that when the car hiccuped the tps was reading 0% even though i knew i was into the throttle. I immediately assumed the tps was bad and changed it and the problem was fixed. there were never any error codes for tps but i was definitely the problem.

I have adjusted fuel over cutoff both map and tps . the tps reads 0 at idle and is calibrated properly . I am still stupmed by this problem . problem also seems to be worse when cold

Ok im having a issue with my car. When driving light thorttle the car studders or hiccups you could say and drops lean right off the gauage(aem wideband) . It only does this under 10% throttle , above that and WOT the car works perfect . I have reloaded a new map more then once and still have the ...

Driving a 2000 Si, with smanager went to do a datalog, completed the datalog and started to make my adjustments. Once i finished my adjustments, with real time updates we did one more datalog, finishing my adjustments for that datalog, i clicked the upload button to ensure changes made in the ...

i have purchased a p30 ecu to use with my hondata s300. I currently have it in a p28, but would like to switch it over to the p30 for the knock sensor. when i took the cover off the p30, i noticed the spot that you have to chip, is located directly under neath the circuit board. is there a different ...

I have S300, and i didnt think the p28 has a knock sensor ability but im getting a code for a knock sensor. i drive a 99 DX, so it doesnt have a knock sensor wiring.


Is a knock sensor able to be used in the p28,