Hondata

Hello, will the speed limiter option soon added to the CRZ calibrations ? it seams not important for many people but for us it is..

Many thanks and very good job on all your very good products!

Hello EITCP,

I was fooled by the fact to entry my wideband signal in the O2 input. I had all tuned in open loop everythink ok but when swith in closed loop it was around 30% too lean column 1 and 2 and 20% 3 and 4 and so on till 8% too lean at WOT. (not boosted)

So if you made the same mistake as ...

Oh my got, everything ok now.... :D

I really thought that the entry with the wideband in the O2 input was Ok. I tried in the ELD input and everything is OK!!

I was very fooled by the fact that in open loop it work but the table is altered by this in closed loop..

Sorry having you disturbing ...

Here is how I connect the wideband:

I cut the white wire (O2 wire) and install a micro plug. That allow me to connect either the 0-5v from the wideband or the stock O2 sensor wire. (but never both signal)

So when I tune open loop I plug the wideband 0-5v in the input O2 and set in the option menu ...

Oh, Spunkster, Is there a difference using the O2 input or the D10-ELD Input with the wideband?? I have not tried using the D10-ELD, I just plug the Wideband in the O2 input and then changed the parameters to stock O2 (quick setting) to read the O2 sensor in closed loop.

Am I right??

Yes a AEM UEGO gauge. Open loop connected to the O2 input with the parameter from AEM like 0.75v=11.5ARF, 1=12, 1.25=12.5, 1.5=13 and so one. I also controlled the voltage offset which is -0.17v to have the gauge and the s200 with the same value.

I already used this Wideband to tune an ITR but with ...

Hello,

Here are the BIN files with new datalog file recorded just a few minute ago.

There are 1 BIN open loop and 1 CLOSED loop with my actual calibration and each datalog file recorded.

As you can see open loop there is INJ 2ms and in closed loop the same but with 38% short term correction ...

Hello,

Here are the BIN files with new datalog file recorded just a few minute ago.

There are 1 BIN open loop and 1 CLOSED loop with each datalog file recorded.

As you can see open loop there is INJ 2ms and in closed loop the same but with 38% short term correction...

When in closed loop mode ...

Ok, I will make a BIN tomorrow with datalog.

Have a nice day.

here the calibration .BIN I've made by mistake the day before. It should be similar column 1 to 5 but column 6 to 10 not fine tuned. (the BIN file is from Saturday but I fine tuned the column 6 to 10 Sunday and haven't the s200 cable here at home...)

Do you think it could come that I made the whole ...

Hello Spunkster,

I haven't answer you correctly as you maybe understand that I changed the voltage target and have no more problem... No, to be more correct, I changed to 0.45v and then it was also to about 15-20% short term correction... (with long term also)

I compared two datalog records to ...

Yes I tried. It was first to 0.51 I think, and I had to change it to 0.45 which is the stock voltage for 14.7 following the stock O2 setting in the seting menu. So after corrected the around 20% requested by the short term, it was well working around 0.45.

The O2 is the stock sensor from the car ...

Hello EITCP,

It's seems that I have the same problem... Everything ok in open loop and then when switching in closed loop, the short term compensate to about +20% fuel... Like my map is really too lean at idle and column 1... but in open loop I am at 14.7...

Did you find something about this ...

Hello,

I just tuned the whole week end a b16a with the s200. Everything was very good and the column 1 to 5 at 14.7. After all the test I then switched to closed loop to control that everything will going right. At Idle the short term correct to about +20%... (too lean..) so then I tried to come ...

Thanks Spunkster. So it's not recomended to plug or unplug the laptop with the motor on.. Ok my laptop USB work well with the s200.

So I will send the s300 to CPL Racing to check it. Thanks