Hondata

CalibratEd wrote: Wed Nov 29, 2023 10:24 pm That is strange. I am not sure why it did that. I adjusted the fuel a bit more. Create a similar log.

- Ed

Hey sorry for the delay Ed, I got a bad snowfall so I won’t be able to create another log until the roads clear up a bit as my car only has summers.

CalibratEd wrote: Mon Nov 27, 2023 11:41 am I adjusted the fuel a bit. Create a normal drive log.

- Ed

At the end of the log when I was in neutral the RPMs went down to about 300 or so like it wants to stall out. Only happens at around 20kmh.

Fueling looks better. Create another log.

-Ed


Hey,

Thank you for all of your time Ed, I really appreciate it!


Thanks for the appreciation. I apologize for the delayed response. I will review the file when I get a chance.

-Ed


Not a problem at all, take your time. Sorry I wasn’t ...

CalibratEd wrote: Sun Nov 19, 2023 3:57 pm Fueling looks better. Create another log.

-Ed

Hey,

Thank you for all of your time Ed, I really appreciate it!

CalibratEd wrote: Sun Nov 19, 2023 3:57 pm Fueling looks better. Create another log.

-Ed

Sorry, ignore my last comment it stopped doing it. The car is running a lot better.

CalibratEd wrote: Sun Nov 19, 2023 3:57 pm Fueling looks better. Create another log.

-Ed

When the car would slow down to around 20kmh in neutral, a couple times it wanted to stall then it would rev up to around 1400 on its own to keep it from stalling. Not too sure what would cause this.

CalibratEd wrote: Sun Nov 19, 2023 3:01 pm I overshot the fuel changes a bit. Create another normal drive datalog.

- Ed

CalibratEd wrote: Sat Nov 18, 2023 7:21 pm I reduced the fuel a bit more. Create another log.

- Ed

CalibratEd wrote: Sat Nov 18, 2023 2:04 pm The car is running rich. I mad some broad fuel changes to lean it out a bit.

Create another normal drive log.

- Ed

Post the updated calibration file and a datalog. I can look over it and better assist you.

-Ed


I should add that when I started the car warm after going to the store, it started right up but then stalled out on me after a few seconds. Not sure if it’s a cranking fuel trim problem or what. I ...

Post the updated calibration file and a datalog. I can look over it and better assist you.

-Ed


datalog0005.fpdl
Factory Setting MAP Tune.fpcal

After changing it to speed density my car definitlely runs different. On startup it seems like the engine wants to cut out a little bit, but then ...

The car is running rich. The MAF table needs to be adjusted. Ideally when you change the intake you should switch it to run on speed density.

-Ed


Thank you for your help!! Running off speed density is using the MAP sensor instead of the MAF correct? Sorry I’m a noob when it comes to this ...

CalibratEd wrote: Wed Nov 15, 2023 10:11 pm The car is running rich. The MAF table needs to be adjusted. Ideally when you change the intake you should switch it to run on speed density.

-Ed

Thank you for your help!! Running off speed density is using the MAP sensor instead of the MAF correct? Sorry I’m a noob when it comes to this stuff.

Welcome to the forum.

Post the calibration and a datalog of normal driving. I can take a look at it.

-Ed


datalog0004.fpdl

I am currently on the factory settings calibration because it seems to run smoother than the reflash.

Post the calibration file you are running.

-Ed


Factory ...

CalibratEd wrote: Sun Nov 12, 2023 8:13 pm Welcome to the forum.

Post the calibration and a datalog of normal driving. I can take a look at it.

-Ed

I am currently on the factory settings calibration because it seems to run smoother than the reflash.