Search found 9 matches

by WickedOne
Thu Aug 17, 2006 10:20 am
Forum: s300 / SManager
Topic: My hondata S300 Daughter board FRIED???
Replies: 16
Views: 15334

I would check the firing order on the distributor ..
by WickedOne
Fri Jul 07, 2006 8:42 am
Forum: s300 / SManager
Topic: s300 and xs quad stage
Replies: 2
Views: 2238

With the s300 it is not possible to hook up a quad stage boost controller. The s300 only has two Auxillary outputs.
by WickedOne
Thu Jul 06, 2006 7:52 pm
Forum: s300 / SManager
Topic: Download Calibration from ECU
Replies: 3
Views: 3375

Download Calibration from ECU

As the topic states .. When you download a calibration from the ECU, you recieve a warning message stating "it is recommended to load a file as opposed to downloading it" If you proceed to download the calibration it gives you a message to check parameters etc. what are the type of changes or ...
by WickedOne
Thu Jun 15, 2006 9:50 am
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

Since you socketed the ecu yourself, it sounds like there is more than likely a problem with the ecu and not the s300, as all s300s are tested before being shipped. You will need to fill out the ecu socketing form on our website and send that along with a cashier's check or money order for $75. We ...
by WickedOne
Thu Jun 15, 2006 4:40 am
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

There is no reason to send it for diagnosis if you have not fully tested the vehicle with a stock ecu and injectors. Judging by the fact that you have installed a resistor box, that sound like the most likely cause of your problems. Double check your wiring and compare it to the insturctions for ...
by WickedOne
Wed Jun 14, 2006 9:53 am
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

It sounds like there is either a wiring problem with the injectors, or you have bad or damaged ecu. What happens with the stock injectors and ecu?

Well, i was thinking about trying it with the stock injectors, but since i have a resistor box installed i'm skeptical installed high impedence ...
by WickedOne
Tue Jun 13, 2006 9:26 pm
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

Until you have started the car you will not be able to fully tell if your socketing is 100%. What ecu are you using, what engine do you have?


Spunkster - I attempted to start the car today, no luck .. Not 100% was the cause is but .. only Injector #1 sprayed fuel - 2.3.4.. No fuel sprayed while ...
by WickedOne
Tue Jun 13, 2006 9:53 am
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

Spunkster wrote:Until you have started the car you will not be able to fully tell if your socketing is 100%. What ecu are you using, what engine do you have?
Ok .. I'll be starting the car tonight and will let you know what I see as for Full Functionality of the unit ..

I have a P72 controlling the B18C1...
by WickedOne
Mon Jun 12, 2006 9:39 pm
Forum: s300 / SManager
Topic: S300 install - Confirm status
Replies: 10
Views: 5239

S300 install - Confirm status

Tonight I installed the S300 per your instructions and preparation.

So far so good - Bottom left hand corner indicates its online .. constant green light off the board..

This was installed on a P72, Now just to let you know .. I did not start the vehicle.. due to some other hardware that has to ...