Search found 11 matches
- Mon Jun 28, 2021 3:58 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Thanks so much for all your help!
- Mon Jun 28, 2021 2:25 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Didn't feel much different from the previous revision and everything looks ok on my end. Do you think it's ready?
- Sun Jun 27, 2021 3:03 am
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Aplogies for the mixup, I was unable to find the original datalog so I remade it after work today.
- Sat Jun 26, 2021 3:08 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Sorry about that I must have mixed them up. Will look for the correct one tonight after work.
- Sat Jun 26, 2021 1:18 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
I got on this one a lot harder and it seems to do well. Looks like the afrs were less lean at WOT which is nice. My hondata app counted 1 knock however I did not see it on the datalog. Let me know how it looks, unless there are any major issues I'm pretty happy with how it feels!
- Fri Jun 25, 2021 1:47 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
This revision feels really good! The powerband is very useable and doesn't feel sluggish at all. No knocks either.
- Thu Jun 24, 2021 3:32 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Ok, will give it a try tonight.
Btw, do you have a PayPal or Venmo? You’re doing me a huge favor and I don’t want you to work for free.
Btw, do you have a PayPal or Venmo? You’re doing me a huge favor and I don’t want you to work for free.
- Thu Jun 24, 2021 2:38 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Here's the datalog for that file you sent me. Afr's seemed consistent but the vtec was a bit sluggish, maybe it could benefit from being raised higher? I looked over the graph but am still not really too sure how to analyze knock.
- Wed Jun 23, 2021 8:21 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Thank you for this! I’ll flash it on tomorrow morning and post a datalog shortly after.
- Wed Jun 23, 2021 7:44 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
Re: New to flashpro and could use some help
Hello, thanks for the reply. I don’t mind using a different file as I just pulled this off one of the provided maps. Really the only thing I’d want to keep from this file is the 3500rpm launch control, removed rev hang, and a rev limit around 8400. Yes I run 91 octane. I plan to keep this tune for a ...
- Wed Jun 23, 2021 6:03 pm
- Forum: FlashPro Calibrations
- Topic: New to flashpro and could use some help
- Replies: 21
- Views: 5817
New to flashpro and could use some help
Hi everyone,
I recently purchased flashpro for my 08 civic si and I'm looking for some help making minor adjustments to a basemap to ensure my car is running safely until I install my bolt-ons and get a proper dyno tune. The car is stock except for a ... test pipe and a skunk2 2.75" exhaust. Below ...
I recently purchased flashpro for my 08 civic si and I'm looking for some help making minor adjustments to a basemap to ensure my car is running safely until I install my bolt-ons and get a proper dyno tune. The car is stock except for a ... test pipe and a skunk2 2.75" exhaust. Below ...