Hondata

Spunkster
What's the process for 2007 FD2 JDM Civic Type R Hondata reflash ?
I do have a spare ECU.

a) Do I send it to Hondata thru' a dealer? Have it reflash by Hondata and then shipped back to me.

b) Does the dealer does the reflash of the ECU.

I would assume it works the same as KPRO, with ...

Spunkster

Everything seems to be working.
The noise is knocking. Turn on the MIL light and datalog to confirm, shows knock counts etc. These calibrations:
K20a2-rsx-stock.kal
K20a2-stock-tuned.kal
K20a2-310cc-itrcams-jrhdr-c...

I tried all above causes knocking. It starts approx @ 2300 rpm and ...

a) What is a good starting point MAP to use for a stock JDM DC-5 Integra type R ? KPRO ECU is a PRB US RSX Type S. It has a A001 suffix. What does the A stands for ? (auto?)

I tried K20a2-rsx-stock.kal
K20a2-stock-tuned.kal
K20a2-310cc-itrcams-jrhdr-c...

There seems to be a strange noise when I ...

Spunkster

You are right, I checked, my mid 2005 JDM DC-5 Type R ECU is :
37820-PRC-J01.

I should be able to use the stock primary 02 sensor as well, am I correct ?

The other question, is assuming I do not want the immobiliser function at all, the PRB ECU that I will purchase, modified for KPRO ...

I am currently a S200 user.

I have a mid 2005 JDM Honda Integra Type R. I just want to make sure I understand. I can purchase a used/new 02-04 ECU, convert it to KPRO. Purchase an adaptor cable (Hondata), to be connected between stock DC5 harness and the converted KPRO ECU. Replace the stock 02 ...

Spunkster

I had to wait for a new set of S200/Gsensor before I can return the set to you for checking. The new set just arrived yesterday. Today, I have forwarded the problematic S200/Gsensor set to you. You should have it in a week. I have attached description and notes of the problem discussed ...

Hondata/Spunkster

Is it normal to get Check Light Code 1 (O2 sensor) running open loop ?

O2 sensor is stock 4 wire. When ignition is on initially, check light does not come on at all. Everything seems normal. Only after about 30 mins of driving (average 3000 rpm, max 4000 rpm), check light Code 1 ...

Hondata

The PDCTU-M9-6 cable that I bought was wired DB9 female pin config vs male pin config. PN is sending me a new one. Meanwhile I rewired the PDCTU-M9-6, use the M505 and hotsync/modem utility, it can communicate with a Sporster modem and dial out - no problem. I tried using hotsync/null modem ...

Spunkster
After calibration, I click stop calibration. Verify, but it's so sensitive that red dots jumps all over as I move the s200 in a circle.

Spunkster

No I didn't dropped the interface box or gsensor, just fiddled with the calibration utility/function, and it gets very sensitive. Tried many times calibrating, couldn' t get it back like original. During calibration, using the wrist, move the s200 in a circle on a horizontal plane for two ...

Spunkster

I recalibrated a few times following the G100 manual but I still have the Gsensor being too sensitive. Did 2 much shorter recording.
I have attached :

a) Recording for car engine idling and stationary. The red dot in the Gforce traction circle graph is moving alot even though car is ...

Spunkster

Thank you for taking your time in helping. I really appreciate this excellent support.

a) The 1st file with low activity is mar24-2005-p08-test02.txt , which you mentioned as first recording . The Gsensor was new -- factory calibrated . I thought it was good because street driving with ...

Spunkster

I downloaded the two files that I have attached to previous post. Opened them with Hondalogger version 3.6.1.0 running on Windows 98. USe Microsoft IE 6 reading forum.

Check/confirm OK --- for Hondalogger GRAPH MENU, I can see GForceLat/GforLong plotted for both files. For GFORCE MENU ...

Hondata

Thank you very much

I attach:
a) mar26-2005-p08-test1.txt ------ Hondalogger Datalog with problem (too sensitive after I calibrated it. Don't know why?)

b) mar24-2005-p08-test2.txt ------ Hondalogger Datalog without problem(factory calibrated by Hondata). torque/Horsepower curve ...

Hondata

I try using a Palm IIIxe and hotsync with a null-modem yesterday and Palmlog works.

I ask Purple Data Cables they told me the pin-out of PDCTU-M9-6 and the pin-out as follows:
Here?s the pinout on the DB9 end:

# Signal
1 n.c.
2 RX (Palm receive)
3 TX (Palm transmit)
4 DTR (Palm DTR)
5 ...