Hondata

go to lordco. if you have one. or anywhere that sells niehoff. part # SL31691
i was able to match the part number spunkster gave me to this part number in canada. tell them its a brake switch

yeah i know what you mean. if there was an upgrade option to the s300 i would do that instead. but the problem could be due to needing a firmware upgrade. i was emailed by a hondata staff it needed that but i can't really afford having the downtime cause its my only vehicle and my daily driver and ...

thats the same problem i have. i can only change it when i connect with my laptop. it detects my brake as well and everything else works besides the brake pedal setting. i didn't bother fixing it. i just set it once and thats about it

is it possible we'll see an update that will work with zeitronix in the future?
http://www.zeitronix.com/Products/zt2/V_AFR.jpg
from zeitronix data sheet
Volt:|0.15|0.31|0.46|0.62|0.78|0.93|1.09|1.24|1.40|1.56|1.71|1.87|
AFR:|9.70|9.90|10.1|10.3|10.5|10.7|11.0|11.4|11.7|12.1|12.4|12.8|

Volt:|2.02 ...

according to there data sheet. its starts from 0.15v:9.7a/r to 3.27v : 21.2a/r
the readings are off by alot.

all wires are soldered according to installation manual. datalogs perfectly with the zeitronix software. but i would like to use the romeditor software to datalog. i used the ar/volt readings that came with the wb but doesn't come close. my readings on hondata don't even move. reads like 10.xx when ...

in static mode. its still in blinking mode when i step on the brake.
i did reburn the chip i can now adjust vtec only through hondalogger.
thing is hondalogger does see the clutch and brake when pressed.

S200-1011 it matches the circuit board inside.

i checked with hondalogger. it detects the clutch and brake when i step on it.
thing is i can change the 3-step/launch in hondalogger but not with the switch/brake pedal. so everytime i wanna change it i have to do it with the laptop. also it won't allow me to change the vtec or revlimiter. it only ...

never tried datalogging yet. i checked the pin d2 which is brake switch
it shows voltage everytime i step on the brake. no volts when not touched.
could it be ecu? but everything else works but also i cant reset it to defaults. which launch it 3k. tried holding switch and turn on but still ...

k i got it working now but its set to 4500 for launch. i can't reset it tried but still no go. i tried static and dynamic. doesn't seem like it recognizes when i tap on the brake pedal. button switch works when i press it. goes through 1-5 but tap on brakes doesn't change anything. tap brakes but ...

thanks spunkster!
i bought a new switch. i'm located in canada and gave them that part# by wells and they gave me this. its a different brand but they were able to match it to this.
does it look correct? i'll try installing it asap. its a two wire switch. i was wondering whats so special about this ...

it looks like a brake switch, the one closest to you with blue stripes(two wire) http://crew08.homestead.com/files/switch.jpg
i'm running a base P30 map i made with romeditor3.6. my car is basically stock with just intake/exhaust right now. 94civic hatch jdm b16a, p28.
car runs great smooth idle ...

i bought this used. s/n:S200-1011
it has all options enabled.
i just installed it a few days ago. installed the clutch switch directly to the box and i can't get it to work. i already tried re-setting the box. holding the button for several seconds while switching the ignition on . still no go. do ...

Hondata wrote:s200-0527 has 3 step but no datalogging nor boost.

can you please check what options i have as well. S200-1011.
i bought it used but don't seem to see the g-module in it.
thanks in advance!